Eagle Z402 Tube Roller, Roll Bending Machines, Angle Rolls at Van Sant Enterprises, Inc.

Eagle Z402 Series Roll Bender
Flats 4 " / Tube 2-3/8" / Angle 1-1/2"
Rugged, Versatile and Highly Cost Effective.

ZH402 Shown Be the first to review this product!
	The New Z402 series are three roll, pyramid type Universal Roll Bending Machines with manually or hydraulically adjusted forming roll and dual driven lower rolls. The detached control stand with LED digital display monitors the bending roll and aids in precise positioning for greater accuracy in rolling. The unit uses the Powerful Pyramid Geometry with lower rolls driven and fixed in position and the top roll adjustable to obtain different bending diameters. Universal tooling supplied in 18 components permit bending of most all standard sections. STANDARD FEATURES LED Digital Display to monitor top roll position Shafts Heat Treated and precision and precision ground Hardened Universal Rolls, New Design more versatile Rugged Steel Heads, No Castings! 2.25 HP Bi-directional TEFC Motor 3 Way Adjustable Lateral Guides All shafts Journaled in dual high load roller bearings Automatic Top Roll Locking Pin for *EASY* tooling change out Higher Rolling Speed & Heavier Machine Weights Low Voltage Controls Thermal Motor Overload Protection Dual Emergency Stop Palm Switches Unit operates in Vertical & Horizontal Positions

Optional Equipment Rolls for round tube/pipe/rod, special sections & serial production requirements Special Lateral Guides with adjustable cam rollers and anti-torsion supports for leg-in angles, *Special Conical Rolls* for angle rolling leg in or out Special rolls for tight diameters Special rolls for wide flats, 8" x 1/8" max capacity Bar Twisting Device - Scroll Bending Device - Cap Rail Solution

ZM-402* (Manual adjustment w/LED, foot pedals, 220v 3ph)
ZH-402* (Hydraulic adjustment w/LED, foot pedals, 220v 3ph)

* This product ships via motor freight only. Shipping charges for this item will NOT be reflected in the shopping cart. You will be contacted with a shipping quote prior to shipment.

CAPACITY CHART

MATERIAL	Z402 Series
Flats, Hard	2 x 3/8 Ø 16"
Flats, Easy	3 x 5/8 Ø 16"
Square Bar	1-1/8 Ø 24"
Angle, Leg-out	1-1/2 x 3/16 Ø 20"
Angle, Leg-in	2 x 1/8 Ø 24"
Tee, Leg-out	2 Ø 28"
Tee, Leg-in	2 Ø 20"
C, Leg-out	2 x 1/4 Ø 14"
C, Leg-in	2 x 1/4 Ø 16"
Round Bar	1-1/4 Ø 24"
Pipe, Sch. 40	1-1/2 Ø 30"
Round Tube	2-3/4 x 18 ga Ø 40"
Square Tube	2 x 2 x 11 ga Ø 40"
Rect. Tube	2 x 1 x 11 ga Ø 56"
Bending Adjustment	Manual or Hydraulic
Driven rolls	2
Rolling speed fpm	14
Working plane	Vertical/Horizontal
Repeat control	LED Readout
Installed power HP	2.25
Approx. dimensions	28 x 38 x 54h
Approx. Shipping wt. lbs.	870

Chart indicates minimum suggested inside bending diameters at maximum section size using mild steel - Specifications subject to change/modification without prior notice - Data is approximate - Contact your authorized dealer for specific tooling capabilities/requirements on shapes and sizes to be bent. Special rolls and/or tooling may be required for some angle, channel rolling and/or for serial production on some sections - Bending I.D.'s may be limited by predicted material distortion.